Ground Control Street Coilover Kit BMW M3 E46 01-05

ImportParts.co.za is an authorized Ground Control dealer for all your suspension needs. We carry the Ground Control Street Coilover Kit for the BMW M3 E46 01-05. Utilizing fully adjustable Koni shocks, and Eibach springs, Ground Control builds a coilover designed to make your E46 M3 handle amazing on and off the track.

Complete Front Strut Housing Machined from seamless DOM 1026 steel alloy tubing. High clearance sway bar bracket welded on.

Koni Single Adjustable Front Strut Struts are externally adjustable from underneath the hood, even with the factory strut brace. This strut is prepared for coil over use, and eliminates machining of critical suspension components .

Click on the following 2 links to learn why we don;t cut threads in our strut housings. Aspects & Keeper

Ground Control Threaded Sleeves This system is designed to eliminate stress risers caused by machining notches into the strut housing. Unlike other companies that claim superiority by cutting threads into a critical component of the suspension, Ground Control uses engineering common sense to maximize the strength of the suspension.

Ground Control Adjustable Spring Perch A unique design, that uses an allen head bolt to clamp the single threaded perch into the correct position. No secondary pieces are needed to "jam" the threaded perch into position. This method of clamping onto the threads also prevents sand, grit, and water from getting into the threads, which is a common problem with jam nuts.

2 SHORT Koni single adjustable rear shocks

Koni Single Adjustable Rear Shocks Preadjusted to match rear spring rates using our shock dyno. The street/track is now exclusively the "top-adjust" version, which adjusts from inside the trunk with no tools needed. The rear shocks are custom built and valved by Koni to GC specifications, and are shorter than standard Konis.

4 Eibach ERS springs, driver school or track event rate

Eibach Spring All poular street spring rates are available. Ground Control springs are made by Eibach on German machines both in the USA and in Germany, however all Eibach springs have a lifetime guarantee against sagging, rate change, or any manufacturing or material failure. Lifetime guarantee. Compare.

4 Ground Control bump stops (made in Germany)

Ground Control Bump Stop We do not just ask you to reuse your stock bump. The stock bump stop is designed for stock suspension we provide a bump stop designed to work with our suspension. These are soft foam, same quality as OE BMW parts, but made to our specs in Germany. Our race bump stops are even different than our street bump stops.

2 rear ride height adjusters

Ground Control Rear Ride Height Adjustment Kit Billet aluminum threaded adjusters bolt on top of the rear control arm. The e36 M3 has a larger diameter rear axle than the standard e46, so it is necessary for clearance to not have any portion of the adjuster below the control arm.

* Suspension is shipped completely assembled and preadjusted*

1 Pair front Camber Plates

Ground Control Racing Camber / Caster Plates More camber adjustment than stock, caster adjustment, aircraft bearing, engraved with calibrated degrees, with stainless steel reinforcement. Every component is anodized or plated, including fasteners. Adds extra travel to avoid excessive bottoming out, this is a very well engineered product. The stainless steel reinforcement prevents electrolysis between the steel fender and the aluminum camber plate.

Camber is quickly adjustable by sliding the mounts, without removing any components from the car. The priority of this design is to allow fast, repeatable alignment changes at the track. Caster is adjustable, when necessary to correct tha car, by changing a shim under the plate.

The Ground Control camber plates feature a urethane bushing that carries the side loads only, and does not rotate (no squeek!) and allows for articulation of the shock shaft. This urethane bushing is very under stressed, as the Ground Control design does NOT support the weight of the car on the urethane bushing. Instead, the weight of the car is supported by a completely separate rotating ball bearing, which is also manufactured in Germany. The entire assembly is machined at an angle, just like the stock upper mount. Beware of less expensive machining that bends the strut shaft after installation.

1 Pair rear upper shock mounts

Ground Control Rear Shock Mount Billet aluminum, urethane bushings, pre assembled. Includes gaskets and reinforcements.

* Suspension is shipped completely assembled and preadjusted*